Cleverscope Model CS328AE - Ethernet Oscilloscope Spectrum Analyzer and Logic Analyzer. 10 bit 100 MS/s, 2 analog channels, 8 digital channels, external trigger, 4M sample memory depth for each of the 2 analog and 8 digital channels. The powerful Windows software allows intuitive operation and graphic display of the data. The Ethernet interface is electrically isolated from the PC.

Features

• Two 10 bit analog channels simultaneously sampling at 100 MS/s, AC or DC coupling
• Streaming transfer to PC hard disk with up to 1.5 MS/s at full 10 bit resolution (ENOB), for up to 200G samples
• 10/100Mbit Ethernet interface to PC
• Scaling of amplitude is automatically adjusted from 20 mV to ±200 V (per division) depending on graphical display and divider ratio setting on probe.
• Automatic offset setting corresponding to the amplitude setting. For example, a curve with an amplitude of 2.4..2.42 V automatically selects a 20 mV range at +2.40 V offset. This is handy for viewing small signals in single supply OP circuits.
• Analogue triggering of the signal curve with regard to a resolution of 1% of the display height. The analog trigger can optionally be preceded by a low-pass, high-pass or noise filter.
• External trigger input, threshold adjustable from 0 to ±18V in 40 mV steps
• Eight digital inputs scanning at 100 MS/s, threshold adjustable 0 to 10 V in 10 mV steps
• A dual hardware trigger system responds to rising or falling edge of any input signal, optionally combinable with a user definable bit pattern at the digital inputs. Triggering occurs when one or both trigger conditions are met and the time between triggers is less, greater or within a definable range, or the trigger timer corresponds to a user definable value
.
• Each channel (2 analog channels, ext. trigger and 8 digital channels) 4M Memory depth for up to 20 ms simultaneous recording per channel at 10 ns resolution
• The value memory can allocate between 2 and 3000 frames in variable sizes from 4M to 2000 samples. This can be used to store a history to re-check previously recorded signals or to capture up to 3000 trigger events with minimal delay between frames while maintaining the time reference between the first and all subsequent frames
.
• 20 MHz Anti-Alias Filter 5th order for optimal performance of spectrum analysis
• Trigger status LED and power LED on front panel
• Power supply: 6..12V, 6W via universal power supply unit
• Low jitter (1 ps_eff.) of the sampling for 70dB dynamic range
free of jitter
• self calibration for highest accuracy
• Dimensions: 153 x 195 x 35 mm

CS300 Application software

• independent, freely movable and scalable windows for displaying the signal, a zoomed signal section and the frequency spectrum
• spectrum analysis with a wide range of analysis options and display in logarithmic and linear formats
• Each signal window contains a time and amplitude cursor and 2 markers for comparison purposes
• Signal average calculation (exponential, block and peak hold) and lowpass filter
• Signal measurements including peak-to-peak, rms value, DC, pulse width, period and frequency
• Comprehensive mathematical functions including + - / •, x², advanced analysis functions, integral and filter functions
• Up to 8 user definable mathematical equations
• Calculation of derived values: frequency, root mean square value, peak value, period, DC, standard deviation, and marker values
• copy/import graphics and data into other programs
• Save to and Öopen from storage medium
• User definable units, signal names and scaling
• adding comments to each curve
• Mathematical formula editor with real-time Matlab transfer
• Protocol Decoding for SPI, UART, I²C and Bus

Scope of delivery of the CS328AE:

• 1 x CS328AE box oscilloscope, 10 bit 4 MSample, isolated Ethernet interface
• 1 x CS1050 Desktop power supply with cable
• 2 x CS1001 250 MHz Passive probe (1x/10x)
• 1 x CS1004/CS1005 8 x 100MHz Digital Pod with Clips
• 1 x Ethernet cable
• 1 x CD with CS300 application software, instruction manual, sample files, videos and whitepapers